Mounting DreamBlack Alloy Steel Speaker Stands, Height Adjustable Bookshelf Speaker Stand Pair, Universal Fit, 11 lbs Capacity, Set of 2 for Bose Polk JBL Sony Yamaha - 42" Max Height

These stands are remarkable. The thought process that went into them is amazing. I have Polk 6.5 outdoor speakers that use the swivel mount which make it hard to put on a standard speaker stand. These work perfectly though. The bolt that locks into the key-eye is fantastic. I can't say enough good things about these.

I got two sets of stands (4 units), added a few silicone pads and Velcro cables ties via Amazon, and now have perfect mounts for the four Quad speakers. The stands are high quality, easy to assemble and versatile.Mounting Dream MD5042-2 speaker stands can be a good solution for mounting Sony Bravia Theatre Quad speakers. Cost is now about $80 for two stands; I got two sets via Amazon and added a couple items to get the kind of mounting I wanted.The stands allow for multiple mounting approaches, but the Quads are of unusual design, so I added two items below for mounting the Quads (I mounted the Quads with their Sony table-stands attached):1. Rubber mounting pads: Hudson Hi-Fi 1" Platinum Silicone Isolation Dot, Non-Skid Isolation Feet - With adhesive back - 20 Duro - 16 Pack (via Amazon, $18). Stick four dots on top plate of each stand to support the Quad-stands (align dots with edge of mounting plate).2. Cable ties: VELCRO Brand ECO Collection | 5 Inch Small Straps for Cords | Reusable Cable Ties | 3/8" Wide, Black, 50 Pac (also from Amazon, about $12). Thread 4 cables ties through the four, 4mm slots in the speaker mounting plate and tighten to secure the speakers on top of the isolation dots. Make sure you’ve installed power cord before mounting speaker.The Mounting Dream speaker height is adjustable and the plastic base-feet are adjustable to correct for uneven floors. The base is “domed” so excess speaker power cord can be coiled and hidden under the base plate. The speaker power cord is hidden inside the support tube.One needs to pull the speaker-end of power cord up through vertical support tube (internal structure of tube prevents gravity feed of speaker-end of power cord). I used an electrician’s fish-tape wire-puller. Something like an undone wire coat hanger would also work.I used twist-ties (from plastic food bags) to temporarily attach the power cord to the fish tape for the pull-thru.Note that the Mounting Dream speaker mounting plate is barely large enough to accommodate the Sony-stand, so use care in aligning silicone dots and speaker base.The isolation dots should align with edge of the mounting plate. You won’t need the MD5042“Speaker Attachment Unit” using the mounting approach described here (you’d only need this if using back-of-speaker mounting hole … a whole different, off-centerline mounting method).

A well built, easy to assemble, adjustable height stand. As other Sony SA-RS5 reviews have noted, you need to go to a hardware store and purchase 5mm screws. As I wanted to mount the speaker right away, I used the keyhole screw to attach the speaker. The problem with this method, and even with a 5mm screw set up, as you tighten it down the sliding rod bends and kicks the bottom of the speaker away from the bar.Two Tips: One, borrowed from Jamie, another reviewer, was to saw off the bottom of the support loop.After ensuring that I had the speaker where I wanted it, and making sure that the support rod was flat against the speaker, I simply wrapped a piece of scotch tape at the bottom of the lower support (the one with 2 screws), removed the support from the speaker and hack sawed it off about 1/16 inch above the tape. I filed any sharp edges. I didn't paint the exposed metal as cutting it above the tape line the support rod is completely hidden withing the bracket. Do yourself a favor. Cut the rod. It's ugly as sin hanging below the speaker.Tip 2: I cut the included plastic spacers in half with a coping saw and then sanded any burrs. I only eyeballed the center and it worked out. I then took the "half" spacer and placed it between the speaker and the support rod. I used a 5mm x 16 cap head screw as they're black and match the stand. This size screw allowed 3 to 4 good thread bites into the speaker which firmly supported it. A 5mm x 20 screw would offer more bite but isn't necessary. If you buy a cap head screw, you'll need a smaller sized allen wrench than the one included with the stand.Using the 1/2 spacer enabled the bar to sit completely flat against the speaker with no bend or kick out. If you don't want to cut the included spacer, use a 1/2" hard rubber spacer from a big box store. They'd be in the specialty hardware section. You may even find them here on Amazon.I wasn't crazy about the plastic feet so I attached felt pads to them. This helped to protect the hardwood floor and gave the added benefit of allowing the power cord to be placed anywhere under the stand bottom.If you have Sony SA-RS5 speakers, you'll need to purchase 5mm screws to secure them to the stand, but these are great, solid, stable stands and worth the money.

Quality Built, easy to assemble. Sturdy. Rear speakers of Samsung HW-Q930D soundbar fit very well and secure! Highly recommended item for rear speakers.